The choice of aggregate industry
We provide all kinds of crushing machines including stationary crusher and mobile crusher
- 0086-21-3390160
- [email protected]
We provide all kinds of crushing machines including stationary crusher and mobile crusher
Aggregate Crushing Value Test -Determine Aggregate
5/5/2010· Procedure of Aggregate Crushing Value Test Put the cylinder in position on the base plate and weigh it (W). Put the sample in 3 layers, each layer being subjected to 25 strokes using the tamping rod. Care being taken in the case... Level the surface of aggregate carefully and insert the plunger so
First, fill the sample aggregate with one-third of the cylindrical measure in three layers Each layer should be tamped 25times freely. After filling the sample aggregate, weigh and record it as W1. Now fill the aggregate in the mould along with the plunger on top. Then place the cylinder on the
How to perform Aggregate crushing value test? Apparatus required. IS sieves of sizes 12.5 mm, 10.5 mm, and 2.36mm. Steel cylinder with open end and dimension of 15.2... Procedure. The aggregate sample is collected from the site. The sample is sieved. This can be done either manually or on...
Aggregate Crushing Value Test Procedure and Result Aggregate Crushing Value Test:. To find out Crushing Strength or Crushing value of Coarse Aggregate. Apparatus:. A 15 cm dia. Steel cylinder with plunger and base plate. A straight metal tamping rod 16mm diameter and 45... Sampling for Aggregate
Aggregate Crushing Value and Its Test Procedure: One of the test in which concrete material can fail is due to crushing under compressive stress. Aggregate crushing test is standardized by IS: 2386 part-IV and used to verify the crushing strength of aggregates. The aggregates should be oven dried, which can passes through 12.5mm and retained on
AGGREGATE CRUSHING VALUE This test helps to determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) 1963. The apparatus used is Cylindrical measure and plunger, Compression testing machine, IS Sieves of sizes 12.5mm, 10mm and 2.36mm. Procedure to determine Aggregate Crushing Value
17/5/2019· The aggregate crushing value test ` gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Aggregate crushing value is defined as the percentage by weight of the crushed (or finer) material obtained when the test aggregates are subjected to a specified load under standardized conditions, and the strength of the aggregate
26/4/2018· Procedure for crushing strength of aggregate. Before testing, the aggregate should be in surface dry condition.You can achieve the dry condition of aggregate by placing aggregates in an oven for 4 hours at 100-degree Celcius. The aggregates passing through 12.5mm and retained on 10mm IS sieves are selected for finding aggregate crushing strength.
19/5/2017· Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.
Aggregate Crushing Value and Its Test Procedure: The cylindrical steel cup is stuffed in three layers of aggregate. Each and every layer is tamped with 25 strokes by the... The net weight of aggregate in the cylindrical steel cup is measured to the nearest gram (W1). The surface of the aggregates is
22/5/2020· For the crushing value test, the following procedure is followed. Procedure for finding the crushing value of aggregate. Aggregate passing through a12.5mm I.S. sieve and retained on 10mm I.S. sieve is taken. About 6.5 kg material is taken. The aggregate in a surface dry condition is filled into the standard cylindrical measure in three layers
Aggregate Crushing Value Test - Procedure And Result Sampling for Aggregate Crushing Value Test: For the Aggregate crushing value test, an aggregate sample passing through 12.5 mm IS sieve and retained on 10mm IS sieve is selected and dried to a temperature of 105 ºC to 110 ºC then cooled to room temperature.
Aggregate Impact Value = (W2/ (W1+W2)) * 100 = 80 gm / 300 gm = 26.67 (Impact Value) Where, W1= Weight of the fraction passing through 2.36 mm IS sieve.(220 gm) W2= Weight of sample retained on 2.36 mm IS sieves. (80 gm) W1+W2 = Total Weight of Sample (220 + 80 = 300 gm) Result: The Aggregate Impact Value is _____. Read More:
27/5/2020· The crushing value of an aggregate indicates its resistance against crushing under gradually applied compressive loads. The standard aggregate crushing test is made on aggregate passing 12.5mm IS sieve and retained on 10 mm IS sieve. Procedure. About 6.5 Kg material consisting of aggregates passing 12.5mm IS sieve and retained on 10mm sieve is
19/5/2017· Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.
General description. The aggregate crushing value (ACV) provides relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. Two versions available: 150 (standard) and 75 mm dia. The apparatus comprehend cylinder, plunger, base plate, tamping rod and measure. Cylinder, plunger and base plate are made
crushes the aggregate to a degree which is dependent on the aggregates crushing resistance. This degree is assessed by a sieving test on the crushed specimen and is taken as the Aggregate Crushing Value. 7.7.1.4 Sampling. The sample used for this test shall be taken in accordance with Chapter 2. 7.7.1.5 Equipment a) Steel cylinder, open-ended, of nominal 150mm internal diameter with plunger and
12/9/2015· Aggregate crushing value = (W1/W2)*100. A value less than 10 signifies an exceptionally strong aggregate while above 35 would normally be regarded as weak aggregates. Also Read: Crushing Test Procedure of Aggregate. Also read: Crushing Value Test Procedure
Original weight of aggregate sample = W 1 g. Weight of aggregate sample retained = W 2 g. Weight passing 1.7mm IS sieve = W 1 W 2 g. Abrasion Value = (W 1 W 2 ) / W 1 X 100. Results
Copyright © 2018 - All Rights Reserved